The Cattron Group International™ PVS800 Portable Video Remote Control System gives the operator clear video pictures of the work zone even when he is not in visual contact with the equipment. The PVS800 provides accurate and safe control with up to three highly accurate camera inputs.

The high resolution, full color PVS800 receiver’s LCD monitor*, with a 5 inch/12.7cm (diagonal) screen, is a stand alone, self-contained module with an integral battery.

Rugged, lightweight and compact components make the Cattron-Theimeg™ PVS800 ideal for tight locations and the harshest environments. Used in mining (for LHDs, bolters, scoop trams, etc.), chemical processing, law enforcement, surveillance, military, bomb disposal, and many similar applications where direct line of sight is neither feasible nor safe.

*The PVS800 monitor is easily installed on Cattron-Theimeg™ AT16LHD and AT32LHD radio remote control systems or on other manufacturers’ equipment.


Key Features and Specifications*

Basic System Components

  • 2 machine-mounted video cameras, housing and brackets (optional third camera)
  • Machine-mounted video transmitter
  • Video receiver/monitor mounted on operator’s portable controller (optional transport case)
  • Can be used with AT16LHD and AT32LHD as well as other manufacturers’ equipment
  • All cables and connectors standard

Video Receiver/Monitor

  • 6 ½ x 4 ½ x 2 ½ inches / 16.5 x 11.5 x 6.4 cm
  • 1.4 kg/3lbs.
  • Color LCD high-resolution display
  • Mountable on a portable controller
  • Self-contained, including battery and whip antenna
  • Rechargeable batteries available
  • 5 alarm messages can be displayed on monitor screen (optional)
  • Monitor transportation case (optional)

Cameras

  • Automatic light compensation, digital processing
  • 3.7 mm standard wide angle lenses (narrow angle lenses optional)
  • Water tight black hardened anodized aluminum camera housing
  • Halogen light assembly optional

Video Transmitter

  • Rugged NEMA 4X stainless steel watertight enclosure
  • Transmits video signal in UHF, 250 mW (900 MHz optional)
  • 8 x 10 x 4 inches / 20.3 x 25.4 x 10 cm
  • Runs on 10 to 36 volts DC
  • Whip antenna
  • 5 Alarm inputs (optional)
  • Audio (optional)
  • Standard range 1500 to 2000 feet

PVS800 – HW

The HW (Hard Wired) version of the PVS800 gives the operator the same clear video pictures of critical areas around the equipment which are not in direct line of sight. Mounted on the instrument panel, power for both the camera(s) and monitor is provided through a single cable attached to the vehicle’s 12/24 volt DC power supply.


Video Monitor:

  • Full color high resolution LCD display, 14.2 cm (5.6 inch) diagonal picture
  • Automatic image reverse
  • Military specification connectors
  • Automatic camera selection when vehicle changes direction*
  • Manual override for forward/reverse camera*
  • 16.5 x 11.5 x 6.4 cm (6 ½ x 4 ½ x 2 ½ inches)
  • 1.4kg (3lbs)
  • Watertight die-cast aluminum housing
  • Brightness control
  • Power on/off switch

* Two camera system only. Check with factory for complete details

Camera (see specifications above)

HW1 – One Camera System

Comes with LCD full color monitor, high resolution color camera with wide angle lens, 12 foot power cable and 33 foot camera cable (other cable lengths optional).

HW2 – Two Camera System

Comes with LCD full color monitor, two high resolution color cameras with wide angle lenses, 12 foot power cable and two 12 foot camera cables. (Other cable lengths and auto select input for reverse camera are optional.)

* Specifications are subject to change without notice.

Truck Example

Low Profile Loader


Copyright© 1997 CATTRON GROUP INTERNATIONAL™. All Rights Reserved. US